Skip to content

Production planning for 3D print farms: plates, printers, shifts

Twenty printers, a hundred orders, six colours and one shift. At some point the plan no longer fits in anyone's head. These are the rules of a good production plan, and how Hive applies them.

AMENT Research TeamPublished 11 min read

Short answer

A good production plan for a print farm sorts orders by urgency, then promised date, then age; never puts different materials or colours on the same plate; and gives each plate to the compatible printer that will finish it earliest. The plan is a draft until a person approves it, and started jobs are never moved. AMENT Hive adds learned print times, shift-aware scheduling that pushes long prints overnight, and a two-date answer to "when will it be ready?".

Key takeaways

  • Keep the ordering rule short and written down: rush, due date, order age.
  • One plate carries one material and one colour; a mixed plate means changeovers and mistakes.
  • A plan is a draft first, and no re-plan ever moves a plate that has already started.
  • Slicer estimates are a starting point; a plan that measures real times and failure rates gets better with use.
  • A shift-aware plan puts long prints at the end of the day and keeps daytime for short plates.

Why is production planning hard on a 3D print farm?

With one printer you do not plan, you just print the next file. Even with five, most people keep an order in their head. As printers, products and colours multiply, the options explode: which order should finish first, which colour goes on which printer, which long print should start tonight?

There are concrete reasons these questions are hard. Each one is manageable on its own, but they all arrive at once and change every day.

  • Different deadlines: a marketplace shipping deadline, your own promise to the customer and a rush custom order all compete in one queue.
  • Changeovers take time: swapping a spool, purging the nozzle and setting an AMS slot each cost minutes, every time.
  • Estimates are wrong: the slicer's time and the printer's real time rarely match, and some printers are slower than their siblings.
  • Prints fail: if a product fails more often on a particular printer, a plan that does not know it stays optimistic.
  • People are not always there: a plate that finishes at night occupies its printer until someone clears it in the morning.

The goal of planning is not a perfect optimisation. It is a draft you can trust each morning, built on clear and consistent rules, that you can update during the day without breaking what is already running.

What should print first? Priority, colour and printer rules

A good planner's rules fit on one sheet of paper. You will not trust a plan whose rules you do not understand, and you will end up fixing an untrusted plan by hand every morning. The planner in AMENT Hive works in three steps, each with a fixed rule.

1 · Order2 · Plate3 · Printer1Rush2Due tomorrow3Due Friday4Oldest order5Newest orderRush → due date → ageOne plate: one material,one colour.B1B2B3K2Other modelThe compatible printerthat finishes first.Started plates never move; a new plan is always a draft first.
First the order (rush, due date, age), then the plate (one material, one colour), then the printer (the compatible one that finishes first).

1. Order: rush, due date, age

Orders marked as rush always come first. Then the due date: here Hive uses whichever is earlier, your promised date or the marketplace's shipping deadline. When dates tie, the older order goes first, so nothing gets stuck behind a steady stream of new ones.

2. Plate: materials and colours never mix

Matched order lines become plates according to their approved print profiles. A plate never mixes profiles, materials or colours. Black PLA and grey PETG cannot share a plate; if they did, you would need a changeover or one of them would print wrong. If a profile's own file is multi-colour, that is a property of the profile; the planner does not invent new colour combinations by mixing orders.

3. Printer: the compatible one that finishes earliest

Each plate goes to the printer, among those matching the profile's printer model and nozzle size, that will finish it earliest. Printers in maintenance, in error or offline are skipped. Planning settings hold the plate setup time, the material or colour changeover time and the QC and packing time per order, and these count too.

Draft plans, approval and jobs that have already started

When you press "Generate plan" in Hive, you get a draft. A draft has no effect on production until it is approved. On the timeline you see which plate starts and finishes on which printer and when, how many plates and units there are, how many changeovers it needs, when everything will be done and whether any order will be late.

Planning · draftToday and tonightStartedPlannedDraftNobody on shiftNight tariff08:0012:0016:0020:0000:0004:0008:00B1 · P1SHinge ×12Lid ×6Body ×2 · overnightB2 · P1SFoot ×8Holder ×10Vase ×3WaitsB3 · X1CLid ×4Clip ×24Panel ×1K2 PlusBody ×1Shelf ×2A1 miniKey fobNow
A simplified drawing of Hive's plan timeline with sample data: started plates, planned and draft plates, unstaffed hours and the night tariff.

Approval belongs to an owner or production manager. At that moment Hive checks the draft is still valid: if a plate has started since the draft was made, a stale draft is not quietly approved; you are asked to generate a fresh one.

  • Started and finished plates never move. Re-planning only changes planned plates that have not started yet.
  • You are told when the plan drifts from the farm: plates that failed since approval, printers that went into maintenance or error, ready orders not in the plan, plates belonging to held orders, or profiles that were replaced.
  • Re-plan in one step: the alert leads to a new draft that fixes the situation, and you approve it again.

This may sound slow. But the most expensive mistake on a farm is a print started last night that appears in the morning to have been swapped for another job by software. In Hive, a person always owns the plan.

Real print times and failure rates: a plan that learns

A plan is only as good as the times it uses. The slicer's estimate is a fair start, but heating, bed probing, AMS colour changes and the printer's own speed settings shift it. Two printers of the same model can finish the same file in different times.

Hive compares the real duration of every finished print with the slicer's estimate. Once the same product has finished at least three times on the same printer model, the planner switches to the median ratio of the last twenty prints, with newer prints weighted more. It also keeps a per-printer correction, along the lines of "this printer is a little slower than its siblings".

Where the plan gets its times from
SituationTime the plan usesWhat you see
Product never printedSlicer estimateSliced estimate, nothing learned yet
At least 3 finished printsLearned timeEstimate and learned average side by side
Slow or fast printerPer-printer correctionThis printer's difference from its siblings

Reprint buffer

The same idea applies to failures. Hive tracks how often a product and a printer failed, or finished with fewer good units, over the last 90 days. If you want, the planner keeps printer time free for the reprints that rate suggests you will need, so the plan is not built on the assumption that everything works first time. Both features can be switched on or off in Settings and are live (✅).

"When will this order be ready?" Two dates, not one

When a customer asks whether an order will be ready by 2 pm tomorrow, giving a single time is easy and misleading. Print times spread out, and some plates get reprinted. The honest answer is two dates: when it will most likely be done, and the date you can safely promise.

When will it be ready?Two dates, not onefinish time →LikelySafe to promiseWanted byCan make itA simulation: nothing is added to the plan.
Illustrative drawing: the spread of possible finish times, the likely finish, the safe-to-promise date and the requested time. The curve's shape is not a measurement.

Hive's "When will it be ready?" tool simulates an existing order, or the lines of an order you have not entered yet, on today's farm. It uses learned times, failure rates, QC and packing time and your staffed hours. The result is two dates, a verdict and a confidence level.

  • Likely: the plan's middle scenario.
  • Safe to promise: the date you can keep even on a bad day, including learned spread and reprints.
  • Verdict: can make it, tight and at risk, or will miss it.
  • Side effects: which other orders would be late if you made this one a rush.

Shift-aware planning and the night tariff

Printers can run around the clock; people cannot. A plate that finishes at 2 am occupies its printer until someone clears it at 8 am. If those six hours are missing from the plan, the plan looks faster than the farm really is.

In Hive you enter staffed hours for each day of the week in Settings. From then on the planner follows these rules:

  • A plate only starts while someone is on shift, and its setup happens then too.
  • A plate that finishes when nobody is there blocks its printer until the next shift, and that wait shows on the plan.
  • A long plate that will run overnight anyway starts just before the shift ends, which leaves the day free for shorter plates.

Optional: night tariff

If you pay for electricity on a time-of-use tariff, moving long prints into cheaper hours can make sense. The feature is off by default. When you switch it on, you enter a price per kWh for each period and an average power for each printer model; there is a ready-made period template for Türkiye's three-period tariff, and you type the prices from your own bill.

The planner only moves long plates into cheaper hours when the due date and the next plate on that printer still hold. Each plan shows an estimated energy cost and the approximate saving from the tariff. For where electricity sits in part cost, see our post on cost per part.

Fitting the most parts on a plate, per printer model

One of the decisions that most affects capacity is how many parts go on a plate. Hand-arranged plates leave wider gaps than they need, because nobody wants to align 24 copies one by one. Every plate is a heat, probe and clear cycle, so more parts per plate means more parts per hour.

Arranged by hand6 partsFill to max24 partsOffset rows, 180° turns, cutter corner kept clear.
Illustrative example: the same part arranged by hand and with "Fill to max". Counts depend on the part and the printer.

Hive works out how many units of a product fit on one plate for each printer model in your farm and compares them: units per plate, plate time, units per hour and filament per plate. The packing tries offset rows, 90° and 180° turns, and keeps clear the areas the printer needs free (the cutter corner on the X1 and P1 series, for example).

  1. 1

    Open the file

    In the catalog, look at the "Best plate for this product" card on the product's file.

  2. 2

    Compare models

    Units and units per hour appear side by side for each printer model, with the best one marked.

  3. 3

    Check it in the editor

    Open the layout in the plate editor; "Fill to max" adds copies of the selected part into the remaining space.

  4. 4

    Save and link it

    Name and save the layout, slice it and attach it to the product's print profile.

A full plate is not always the best plate: a very long plate loses more when it fails, and it may not fit into the daytime plan. So the choice stays with you. For slicing and the plate editor, read our post on cloud slicing. If you would like to try it on your own farm, start a 14-day free trial of Hive.

Frequently asked questions

Does Hive apply the plan on its own?

No. Hive prepares a draft, and the draft has no effect until an owner or production manager approves it. Even after approval, starting each print is a separate human confirmation.

What happens to running prints when the plan changes?

Nothing. Started and finished plates never move during re-planning; only planned plates that have not started can change. If a plate started after the draft was made, Hive asks for a fresh draft.

What if real print times differ from the slicer estimate?

Once the same product has finished at least three times on the same printer model, Hive plans with the real times and keeps a separate correction for slower or faster printers. Until then it uses the slicer estimate and says so clearly.

Does the plan account for prints finishing at night when nobody is there?

Yes, if you have entered staffed hours. A plate that finishes when nobody is there counts as occupying its printer until the next shift, and long plates are started just before the shift ends so they print overnight.

Does a night tariff really save money?

It depends on the price gap in your tariff, the real power draw of your printers and the due dates of your long prints. Hive keeps the feature off by default and only moves prints when due dates still hold. The saving shown is an estimate based on the prices and power figures you enter.

Run your print farm with AMENT Hive

Try Hive free for 14 days; no card needed.