Skip to content

Multicolour 3D printing: AMS, MMU, tool changers and purge waste

From single-nozzle feeders to tool changers: how multicolour systems work, where filament is lost at every colour change, and practical ways to waste less.

AMENT Research TeamPublished 12 min read

4 colours · 1 nozzle

Short answer

Multicolour FDM printing works in one of two ways: feeding different filaments through one nozzle in turn (AMS-style feeders, MMU) or giving each colour its own nozzle (tool changers, IDEX). Single-nozzle systems are common and easy, but they flush the old colour at every change, and on some models that waste outweighs the part. You cut it most by flushing into sacrificial objects and infill, reducing the number of changes and filling the plate with copies. When colour is only a small detail, a single-colour print with assembly or paint is often the better choice.

Key takeaways

  • Single-nozzle systems (AMS, MMU) flush the nozzle at every colour change; that is where the waste and the extra time come from.
  • Tool changers and IDEX flush far less, but they are more complex and usually more expensive.
  • The biggest savings: flush into sacrificial objects and infill, make fewer changes, and fill the plate with copies.
  • Dark to light is the most expensive change; colour order and part orientation make a large difference.
  • When colour is a small detail, printing in one colour and assembling or painting is often faster and cleaner.

How multicolour 3D printing works

An FDM printer draws with a single thread of molten plastic. If a layer contains two colours, the printer has to switch material somewhere. There are two basic ways to do that: push different filaments through the same nozzle in turn, or give each filament a nozzle of its own.

With one nozzle, some molten plastic of the old colour stays inside the hot end. That mixed section has to be pushed out until the new colour runs clean. This step is the source of the waste, the extra time and the reputation multicolour printing has for being expensive.

With several nozzles, each colour waits in its own. The change is a mechanical move and there is very little mixed material to clear. The price is a machine that is more complex, heavier and usually more expensive.

AMS, MMU, tool changer and IDEX: the differences

Four multicolour systemsAMS-style feederOne nozzle, a purge on every changeMMU selectorSelector and one nozzle, wipe towerTool changerA nozzle per colour, little purgingIDEXTwo independent heads, two colours
Four approaches: a feeder and a selector that bring filament to one nozzle, and a tool changer and IDEX that give each colour its own nozzle.

AMS-style feeders

Several spools sit in a closed box. Each has its own feed motor, and the filaments merge in a hub into a single tube. According to Bambu Lab's wiki, an AMS has four feeders, and on the X1 series an AMS Hub lets up to four AMS units connect to one printer. At each change the filament is cut at the toolhead, wound back, the next one is loaded and the nozzle is flushed.

The appeal is convenience: load the spools, assign colours in the slicer and the printer does the rest.

MMU and selector systems

In systems such as Prusa's MMU3, filament comes from fixed spools and a sliding selector pushes the right one into the extruder. Prusa says the MMU3 switches automatically between five filaments. The logic is the same as the AMS: one nozzle, a flush at every change and a wipe tower beside the print.

Tool changers

Each colour or material waits in its own toolhead with its own nozzle, and the carriage picks up and drops off the head it needs. The Prusa XL takes up to five heads. Prusa says there is no purge waste because each head keeps its own nozzle, and that parked heads stay preheated. In practice a waiting nozzle can ooze a little, so in most set-ups a fresh tool does a short prime before it prints. Even so, the waste is far below single-nozzle systems.

IDEX

IDEX (independent dual extruders) uses two separate carriages with two nozzles. It suits two-colour prints, or a build material with a soluble support, and some machines can print two copies or a mirrored pair at the same time. The limit is plain: two colours.

Multicolour systems at a glance (colour counts from manufacturers' published information as of October 2026)
SystemNozzlesColoursPurge wasteBest for
AMS-style feederOne4 per unit; several units on some modelsHigh, at every changeDecorative multicolour work, easy set-up
MMU (selector)One5 on the MMU3High; wipe tower and wipe to infillAdding colour to an existing printer
Tool changerOne per colourAs many as headsLowFrequent changes, multimaterial, production
IDEXTwo2LowTwo colours, soluble support, copy printing

Purge and the prime tower: where the waste comes from

Bambu Lab's wiki breaks a single-nozzle colour change into four steps. The old filament is cut and retracted. The nozzle is flushed until what comes out is purely the new colour. The tip is wiped across a wiper. Finally, flow is stabilised on the prime tower before printing returns to the part.

Anatomy of one filament change1Retract, cutThe old filamentis pulled back2FlushExtrude untilthe colour is clean3WipeThe nozzle tipis cleaned4PrimeFlow settleson the towerOld colourFlush volumeNew colour
One single-nozzle colour change: retract and cut, flush, wipe, prime. The strip shows the mixed section discarded on the way from the old colour to the new.

Colour is the main factor in how much has to be flushed. Even a trace of the old pigment stains a light colour. The direction of the change matters: dark to light needs more flushing than light to dark. Black to white costs noticeably more than white to black.

The prime tower is a separate cost. It has to reach the highest layer that has a colour change, so if the changes are only near the top, the tower grows through every layer below with clean filament that serves no purpose. In Bambu's own example, flipping the same part so the changes sit at the bottom made the prime tower about 40% smaller.

How to reduce purge waste

There are two ways to waste less: flush less at each change, or make fewer changes. Each affects the part differently. The chart below places the common methods on those two axes, qualitatively.

Ways to cut waste (qualitative)Start hereEffect on the part's look or design →Power to cut waste →lowhighFlush into supportLower the multiplierBatch copies per plateFlush into a spare objectFlush into infillThicker layersReorient the partOne colour + paint
Ways to cut purge waste, positioned qualitatively. The real effect depends on the model, the colours and the slicer.

Send the flush somewhere useful

  • Flush into a sacrificial object. Add parts to the plate whose colour does not matter: parts you will paint, internal fixings, workshop jigs. In Bambu's example, a cube that would normally need about 70 g of flushing drops below a gram thanks to the sacrificial parts beside it.
  • Flush into infill. The mixed colour goes into infill that is hidden from view. With light or translucent colours, or few walls, the infill colour can show through.
  • Flush into support. Support that will be thrown away anyway is printed with the mixed colour. It is on by default in Bambu Studio; with little support the effect is small. Flushing into infill and support only works with the prime tower enabled.

Flush less per change

Slicers calculate flush volumes on the safe side to protect print quality. Bambu writes that lowering the multiplier to 0.8 or 0.9 can be a quick saving, but that you should run test prints to check the colour transition. Set it too low and it comes back as discoloured layers. You can also tune individual pairs, for example only black to white.

Make fewer changes

  • Reduce the layer count. In Bambu's example, raising layer height from 0.2 mm to 0.28 mm cut the changes from 153 to 111 and the waste from 83 g to 61 g.
  • Orient the part so the colours run parallel to the layers. If colours sit in horizontal bands, there are almost no changes per layer. Lay the same part on its side and every layer contains every colour; in Bambu's counter-example the waste rose 22-fold.
  • Print several copies on one plate. A change on a given layer serves every copy on that layer, so the waste per part drops.
  • Let the slicer set the colour order, or set it yourself. The slicer starts each layer with the colour that finished the last one and tries to pick the order that needs the least flushing.
  • Merge near-identical colours in the design; two similar greys are one more change.

We look at what this waste does to part cost in 3D printing cost per part, and at the environmental side in sustainable 3D printing.

Multimaterial printing: supports, flexibles and abrasives

The same hardware can combine different materials. The most common use is printing the support interface in a separate material: an easy-release support filament, or water-soluble PVA or BVOH. Bambu notes that for support materials the flush volume is calculated not only for colour but also to stop contamination that would make support and part stick together.

Feeders have limits. Bambu's filament table does not recommend soft TPU or damp PVA and BVOH in the AMS. It warns that some brittle or rough fibre-filled filaments can wear the feed channel, and that abrasive materials such as carbon fibre or glow-in-the-dark filaments can eventually grind down the internal PTFE tubes. If you want to join a flexible part to a rigid body, a tool changer or IDEX may be the better fit.

Water-soluble supports take up moisture very quickly and cause feeding trouble if they are not kept dry. Our guide to filament storage and drying is a good place to start.

When single colour, paint or assembly is better

Multicolour printing is not the right tool for every job. In these cases a single-colour print with some finishing is usually faster, cheaper and cleaner:

  • Colour appears in only a small area, such as a logo or lettering. Printing the logo separately and pressing or gluing it in removes hundreds of layers of changes.
  • The part is a figure that will be painted anyway. Primer and paint give more control over transitions and shading than printing does.
  • The part is large and the colours fall into clear zones. Printing the zones separately and joining them splits both waste and risk: if one piece fails, you reprint only that piece.
  • You are producing many units and the changes multiply the print time. Printing single-colour parts in parallel on several printers usually makes better use of total capacity.

Multicolour printing earns its place where colours interlock through the layers, where assembly would be awkward, or where the part has to stay in one piece: maps, signs, name plates, multicolour figures, functional parts with rigid and flexible zones.

At AMENT, colour consistency and lot data are among the goals for the filaments we are developing. They are not on sale yet; you can see the planned collection on our materials page.

Frequently asked questions

Why does multicolour printing waste so much filament?

In single-nozzle systems, molten plastic of the old colour stays in the hot end and is flushed out until the new colour runs clean. That repeats at every colour change on every layer. On models with many changes, the flushed filament can weigh more than the part itself.

Can I turn off the prime tower?

Some slicers let you, but in Bambu Studio the options to flush into infill and support only work with the prime tower enabled. The tower also stabilises flow after each change. Moving the changes towards the bottom of the part so the tower stays short is usually a safer saving than removing it.

Should I buy an AMS-style feeder or a tool changer?

If you print decorative multicolour parts now and then, an AMS-style feeder is easy and sufficient. If you change colours often, combine different materials or print at production pace, a tool changer wastes less and changes faster, but it costs more and is more complex.

Can I print TPU through an AMS?

According to Bambu's filament table, TPU is not compatible with the AMS; soft filaments cause trouble in the feed path. Printing TPU from an external spool, on a system with separate nozzles, or as a single colour is the safer route.

Why does switching from dark to light colours create more waste?

A tiny trace of dark pigment visibly stains a light colour, so the slicer allocates more flushing for dark-to-light changes. Ordering colours so that lighter ones print before darker ones reduces the total waste.

Sources

  1. 1Bambu Lab Wiki: Reduce Waste during Filament Change
  2. 2Bambu Lab Wiki: Connect AMS Hub and multi-AMS
  3. 3Bambu Lab Wiki: AMS main functions and workflow introduction
  4. 4Bambu Lab Wiki: Filament guide, printer, nozzle, AMS and build plate compatibility
  5. 5Prusa Research: Original Prusa MMU3
  6. 6Prusa Research: Original Prusa XL, 5-toolhead

Hear about AMENT filaments first

Our filaments are pre-launch. Be the first to know when measured technical data is published.